ABS Split Front Fog Light Bezel Cover for Model Y Juniper & YL 6-Seater

Split Front Fog Light Bezel Covers for Tesla Model Y Juniper / Model YL

Add a sharper layered detail around the lower front bumper with split fog-light bezel covers designed specifically for the refreshed Model Y Juniper and Model YL 6-Seater. Injection-molded ABS construction and automotive-grade adhesive provide a fitted exterior styling upgrade without replacing the factory fog-light assembly.

Decorative Trim — Not a Fog Light Assembly

This product is an exterior bezel / trim overlay for the front fog-light area. It does not include LED lamps, wiring, bulbs, control modules or replacement fog-light housings.

Sharper Definition Around the Front Bumper

Split Contour Design
Breaks up the broad lower bumper surface with separate sculpted accents around the fog-light recesses.

Factory-Style Integration
The covers follow the refreshed bumper contours for a fitted appearance rather than using universal exterior trim.

Change the Look Without Replacing the Bumper
The accessory installs over the existing exterior trim area instead of replacing the complete bumper or fog-light assembly.

Injection-Molded ABS Construction

Tesery specifies high-grade automotive ABS manufactured using an injection-molding process.

The rigid molded construction is intended to maintain the bezel shape while handling routine outdoor exposure and light road debris.

⚠️ Carbon Fiber Finish — Not Real Carbon Fiber

The current color selector uses “Glossy Carbon Fiber” and “Matte Carbon Fiber,” but the product construction is explicitly ABS. These options describe the carbon-fiber-style appearance and should not be marketed as genuine carbon fiber.

Finish Options

Vehicle Compatibility

⚠️ Not Compatible With

This exact product is not listed for 2020–2024 Model Y vehicles or Model Y Performance. Do not order by vehicle name alone—verify the front bumper and fog-light recess design before installation.

Model YL 6-Seater Compatibility

Tesery specifically lists the 2026+ Model YL 6-Seater as compatible with this split front fog-light bezel design.

Designed Around Factory Openings

The supplier states that the bezel geometry is molded around the factory fog-light area and nearby front-bumper sensor locations.

When correctly aligned on the compatible bumper, the accessory is intended to preserve normal clearance around those areas.

⚠️ Verify Sensor & Light Clearance After Installation

Supplier fitment claims should not replace a physical check. After installation, confirm that no trim edge overlaps a lamp, sensor opening or nearby bumper component and verify that all vehicle functions operate normally.

Exterior Trim Protection

The rigid ABS overlay also creates another contact layer over the covered bumper-trim area.

It may help reduce direct exposure to minor surface scuffs and light road debris, but its primary purpose is exterior styling.

⚠️ Cosmetic Trim — Not Impact Protection

This product is not a structural bumper protector and should not be described as crash protection, impact armor or a component that improves vehicle safety. Strong impacts can damage both the accessory and the underlying bumper.

3M Adhesive Installation

1. Clean the Installation Area
Remove dust, road film, wax and oils from the bumper surface where the bezels will attach.

2. Dry Completely
The mounting area must be fully dry before adhesive installation.

3. Dry-Fit Both Pieces
Position the left and right bezel covers without removing the adhesive backing and verify that the contours match the bumper.

4. Remove the Adhesive Backing
Peel the protective film from the automotive 3M tape.

5. Align Carefully
Match the bezel edges with the fog-light recess and surrounding bumper contours before pressing it down.

6. Apply Firm, Even Pressure
Press across the adhesive contact areas to help establish an even bond.

⚠️ Dry-Fit Before Applying Adhesive

Do not remove the adhesive liner until both pieces have been test-fitted. Incorrect positioning may create uneven gaps, interfere with nearby openings or reduce adhesion if the trim must be repeatedly repositioned.

Removable Adhesive-Mounted Design

Tesery states that the adhesive-mounted trim can be removed later using gentle heat to soften the tape. Any remaining adhesive should be removed carefully with a surface-compatible adhesive remover or isopropyl alcohol.

Use Caution When Applying Heat

If heat is used during removal, apply only gentle, controlled heat and keep the heat source moving. Excessive heat can damage exterior plastics, coatings or paint.

Cleaning & Care

Routine Cleaning
Use normal automotive exterior washing methods with a soft microfiber cloth or wash mitt.

Avoid Aggressive Abrasives
Do not use abrasive pads or harsh polishing compounds directly on the decorative finish.

Inspect the Edges
Periodically check that the bezel edges remain securely bonded, particularly after repeated high-pressure washing or extreme weather exposure.

Specifications

⚠️ Unpublished Specifications

The current exact page does not publish product dimensions, ABS thickness, individual piece weight, adhesive tape width, UV-test data or independent impact / weather test results. Do not add these specifications unless separately confirmed for this exact product.

Package Includes

1 Set × Split Front Fog Light Bezel Covers

Quick Answers