Teskay
Angel Wings Door Welcome Lights for Model 3/Y/S/X
Angel Wings Door Welcome Lights for Model 3/Y/S/X
Couldn't load pickup availability
Angel Wings Door Welcome Lights for Tesla Model 3 / Y / S / X
Add a dramatic illuminated welcome effect to your Tesla without replacing the factory puddle lights. These compact adhesive-mounted LED projectors attach to the lower door area and cast a large wing-shaped pattern onto the ground whenever the door is opened.
Large Wing-Shaped Projection
Projects a long, highly visible wing pattern onto the ground beside the open door for a distinctive nighttime entrance effect.
Adhesive-Mounted Door Design
Installs directly onto a clean lower door surface using the pre-applied adhesive backing rather than replacing the original Tesla puddle-light housing.
Useful Ground Illumination
The bright LED projection also makes the area beside the vehicle easier to see when entering or exiting in a dark driveway, garage or parking lot.
Why These Door Welcome Lights Stand Out
A small module mounted low on the door creates a much larger illuminated graphic on the pavement below.
Because the unit mounts to the door surface, it is separate from the factory rectangular or circular puddle-light housing.
Install one projector on each selected side, typically using the 2PCS configuration on the two front doors.
Choose four projectors when you want the same welcome effect available from four compatible door locations.
Choose the classic feathered Angel Wings pattern or the sharper Evil Wings design to match your preferred look.
Not a Plug-In Puddle Light Replacement
This product sticks directly to the lower door surface. It does not replace the original Tesla door puddle light and therefore does not depend on whether the factory light housing is round or rectangular.
Choose Angel Wings or Evil Wings
The supplied product link currently selects Angel Wings / 2 PCS.
Simple Adhesive Door Installation
Select a flat lower-door area where the projector can aim toward the pavement without contacting the sill or vehicle body when the door closes.
Remove dust, oil, wax and interior-detailing residue from the intended mounting area and allow it to dry completely.
Hold the projector in position first and check where the wing pattern lands before removing the adhesive backing.
Peel the protective liner from the back of the projector only after final positioning has been confirmed.
Apply even pressure across the module for at least 30 seconds to establish adhesive contact.
The current manufacturer recommends waiting at least 30 minutes before repeated door operation and final testing.
Because the projector sits on the door surface, test the selected location carefully to make sure the module does not contact the door sill, weather seal or body when the door closes.
Current installation imagery shows a self-contained adhesive-mounted projector with its own on/off switch. The original puddle light does not need to be removed or modified.
Specifications
| Attribute | Details |
|---|---|
| Product | Adhesive-Mounted LED Door Welcome Projector Lights |
| Source Variant | Angel Wings / 2 PCS |
| Manufacturer-Listed Vehicles | Tesla Model 3 / Model Y / Model S / Model X |
| Mounting Location | Lower Inner Door Surface / Door-Side Area |
| OEM Puddle-Light Replacement | No |
| Factory Light Socket Shape | Not Relevant to This Adhesive-Mounted Version |
| Projection Options | Angel Wings / Evil Wings |
| Quantity Options | 2 PCS / 4 PCS |
| Light Type | High-Brightness LED Projector |
| Activation | Manufacturer States Automatic Illumination When Door Opens |
| Exact Door-Detection Method | Not Published |
| Power Switch | Integrated On / Off Switch Shown in Current Product Images |
| Exact Battery Type / Capacity | Not Reliably Published |
| Wiring Modification | Not Required |
| Drilling | Not Required |
| Mounting Method | Pre-Applied Adhesive Backing |
| Manufacturer Pressing Time | At Least 30 Seconds |
| Recommended Adhesive Set Time | At Least 30 Minutes Before Repeated Door Use |
| Manufacturer-Listed Operating Temperature | -20°C to +70°C (-4°F to 158°F) |
| Manufacturer-Listed Water Resistance | IP65 |
| Published Dimensions | Not Published |
| Package | 2 or 4 Door Welcome Light Projector Modules Depending on Selected Quantity |
Quick Answers
Which exact version is selected in the supplied link? +
Variant 47057981735144 currently selects Angel Wings with the 2PCS quantity.
Is this the same product as the rearview-mirror Angel Wings kit? +
No. The rearview-mirror version replaces or integrates with components underneath the exterior mirrors. This version is a small adhesive projector mounted directly onto the door.
Does this replace my Tesla's original puddle light? +
No. The projector sticks to the door surface and works independently from the factory puddle-light module.
Do I need a rectangular factory puddle light? +
No. This adhesive-mounted version does not occupy the original puddle-light socket, so the factory light shape is not relevant to installation.
Which Tesla models can use it? +
The current manufacturer lists Tesla Model 3, Model Y, Model S and Model X. Because this is a surface-mounted accessory, verify that your chosen door location provides enough flat mounting area and closing clearance.
What is the difference between Angel Wings and Evil Wings? +
Angel Wings uses a long feathered wing design. Evil Wings uses a sharper, more aggressive bat-like wing shape.
Should I choose 2PCS or 4PCS? +
Choose 2PCS if you want two selected doors, commonly the two front doors. Choose 4PCS if you want projectors at four compatible door positions.
How is the light installed? +
Clean the lower door surface, test the projection position, remove the adhesive backing, press the light firmly for at least 30 seconds and allow the adhesive to set before repeated door use.
Do I need to remove the door panel? +
No. Current installation instructions show the projector mounting directly to the visible door surface.
Does it require wiring? +
The current installation instructions and product imagery do not show cutting or connecting vehicle wiring.
What battery does the projector use? +
The current source does not reliably publish the internal battery type, capacity or charging method, so this page does not invent those specifications.
How does it know when the door opens? +
The manufacturer states that the light activates when the door opens, but the exact sensing method is not clearly documented on the current product page.
Is the projector waterproof? +
The current manufacturer specification lists an IP65 water- and dust-resistance rating.
Can the adhesive light be removed later? +
Yes, but remove it carefully using trim-safe heat and adhesive-removal methods to reduce the chance of leaving residue or affecting the door surface.
SKU: TSL2904
