Real Carbon Fiber Front Intake Air Blades Trim for Model Y Juniper & Model YL 6-Seater

Real 3K Dry Carbon Fiber Front Intake Air Blades for Tesla Model Y Juniper / Model YL

Add a sharper performance-inspired look to the refreshed Model Y front fascia with genuine 3K dry carbon fiber air blade trims. Precision-shaped for the front intake area, this 2-piece set combines lightweight carbon construction with a clean stick-on installation.

Performance-Inspired Front-End Upgrade

Sharpen the Front Intake Profile
The left and right air blade trims extend the visual lines around the front intake area for a more aggressive appearance.

Authentic Carbon Fiber Texture
Because the panels are made from genuine carbon fiber, the visible woven pattern comes from the material itself rather than a printed surface graphic.

Designed Around the Refreshed Model Y Bumper
The product is shaped specifically for Model Y Juniper and Model YL front fascia geometry.

100% Authentic 3K Dry Carbon Fiber

Tesery explicitly identifies the material as genuine 3K dry carbon fiber. This exact product should not be described as carbon-fiber-look ABS, hydro-dipped plastic or printed carbon trim.

Airflow-Oriented Shape

The supplier states that the air blade extensions are designed to guide airflow around the front intake area and reduce turbulence around the front fascia.

Their shape follows the factory intake channels rather than covering the entire opening.

Aerodynamic Claims Are Supplier-Rated

Tesery markets the air blades as helping refine airflow, reduce turbulence and minimize drag. No independent wind-tunnel, CFD or vehicle-range data is published on the exact product page, so do not claim a specific drag reduction, range increase or measurable high-speed handling improvement.

Vehicle Compatibility

⚠️ Not for Pre-Juniper Model Y

This exact product is designed for the refreshed Model Y Juniper 2025+ and Model YL 6-Seater 2026+ front bumper. Do not assume fitment with Model Y 2020–2025.03 or other earlier bumper designs.

Model YL Fitment Is Explicitly Confirmed

Tesery specifically lists the Model YL 6-Seater 2026+ together with the Model Y Juniper 2025+ for this exact air blade set.

Finish Options

Designed Around Factory Front-Bumper Features

The supplier states that the trims are 3D-scanned to follow the original bumper channels and are intended to avoid blocking the factory airflow path or front sensing areas when correctly installed.

⚠️ Verify Clearance Before Final Bonding

Before removing the adhesive liner, dry-fit both trims and confirm that they do not cover any visible sensor, camera, vent opening or active grille feature present on your specific vehicle configuration.

Heavy-Duty 3M Tape Installation

1. Clean the Installation Area
Remove dirt, wax, grease and surface residue from the front intake trim area.

2. Dry the Surface Completely
The bonding surface should be clean and dry before adhesive installation.

3. Dry-Fit Both Air Blades
Place the left and right trims against the bumper and confirm the position before exposing adhesive.

4. Use the Adhesion Promoter
Apply the supplied adhesion promoter to the intended bonding area according to the included instructions.

5. Apply the 3M Tape
Use the supplied automotive 3M double-sided tape on the designated rear contact areas.

6. Align & Press Firmly
Position each air blade carefully and apply even pressure across the bonded surfaces.

7. Recheck the Edges
Confirm that every bonded edge sits flush against the factory bumper surface.

⚠️ Dry-Fit Before Applying Adhesive

Do not remove the adhesive backing until both left and right trims have been test-fitted. Incorrect positioning can reduce adhesion quality and may make later realignment difficult.

Install on a Clean, Dry Surface

Avoid installation on wet, dusty or freshly waxed surfaces. Cold conditions can also reduce initial adhesive tack, so follow the tape manufacturer's recommended installation conditions whenever possible.

Removal

Tesery states that the trim can be removed later by gently warming the adhesive with a hair dryer and slowly separating the panel from the vehicle.

Any remaining adhesive can be cleaned using an appropriate automotive adhesive remover such as isopropyl alcohol or a compatible citrus-based tape remover.

⚠️ Remove Slowly

Do not pull the carbon trim away from the bumper abruptly. Use mild heat and gradual pressure to reduce stress on both the carbon panel and the factory painted surface.

Cleaning & Care

Routine Cleaning
Wash the carbon trim using normal automotive exterior-care methods and a soft microfiber cloth.

Avoid Abrasive Pads
Do not use aggressive abrasive pads or harsh compounds on the visible finish.

Inspect the Edges
Periodically check that all bonded edges remain fully seated.

Address Loose Edges Early
If any bonded edge begins to lift, stop high-pressure washing around that area until the adhesive condition has been checked.

Specifications

Package Includes

2 × Front Intake Air Blade Trims
1 × Left + 1 × Right

1 × Roll of Automotive 3M Double-Sided Tape

2 × Adhesion Promoter Wipe Pads

⚠️ Unpublished Specifications

The current exact page does not publish individual panel weight, carbon laminate thickness, resin type, wind-tunnel drag data, CFD results, vehicle-range improvement or a quantified high-speed stability improvement. Do not add those claims unless they are separately verified for this exact product.

Quick Answers